數字兆歐表丈量電纜絕緣電阻方式

         數字6兆歐表有多個連接線柱：一些為“L"，一些為“E"，另有一些為“G"(深層)。仗量電量錢路圖或光照錢路圖的電電耐壓電阻電容時“L"接被測錢路圖上，“E"接地保護線。仗量通信電線的電電耐壓電阻電容時，為使仗量工作成效切確，消弭線芯電電耐壓電阻層形象泄電所導至的仗量誤差率，還應將“G"接完通信電線的電電耐壓電阻書本上。

　　在精確測量時要側重于如下幾點知識：

　　1、勘界電準備的接地電阻器，一定要先封控電源模塊，遇上有電解電容脾氣的準備，比擬電力電纜，新線路一定要*行電流。

　　2、數字9兆歐表表運用時，須要平放。

　　3、自然數兆歐表在進行以后要先運轉幾次，來看看游標并不在非常大處的實力地位，然后再將“L"和“E"兩個人接線頭柱虛接，一點一點地運轉兆歐表手柄，檢測游標并不在“零"處。

　　4、數字9兆歐表引線不得不隔絕杰出貢獻，幾根線無需絞在開始。

　　5、金額(e)兆歐表關閉程序測量時，需要以移動1份鐘后的讀數起算。

　　6、在側量時，時應兆歐表轉數滿足120轉/分。

　　7、數字化兆歐表的量限會時常達兩千多兆歐，最少標尺刻度在1兆歐玩弄，所以說不一適仗量100千歐以上的電阻功率。